MultiWii PRO Ez3.0 Flight Controller w/ GPS Option

 The Evolution of MEGA

 MultiWii Pro V3 Flight controller –Same great sensors as The Mega 2.0, but now with the Ez-connect system. The Ez-connect wiring system makes the initial setup of the flight control board on your copter much easier. Modern processor; latest Gyro/Accellerometer technology; 5v and  3.3v regulators; Spektrum Satellite receiver connection; USB Protection Diodes- the Mega has endless features that are unique to other MultiWii boards.

Includes ALL the Atmega2560 I/O pins that are needed for taking full advantage of the MultiWii and MPNG feature set.

• Modern processor Atmega2560 – Super fast, 4X memory
• 2000 degrees/second 3-axis MEMS gyro + accelerometer (MPU6050)
• 3-axis magnetometer (HMC5883L)
• Pressure sensor (MS5611)
• Flexible motor outputs, support various airframe types –
• Quad/Hexa/Tri/Bi/Y4/Y6/Octo/Camera Gimbal. (Default is Quad-X)
• Up to 8 ch RC input –  standard receivers (PWM), PPM Sum receiver (FrSky, etc), or Spektrum Satellite
• Servo output for camera pitch and roll control
• Supports direct connection of GPS module
• On-board USB connection for programming
• MultiWii-based configuration software for easy tuning.

• Mounting: Standard Mk style mounting holes 45mm X 45mm 
• Dimensions: 70x50x12mm
• Weight: 16g

 

Pre-loaded with QUADX (unless other motor plan is selected, see below) and programmed to fly almost out of the box with most any ESC’s.

One 10-pin Radio Rx cable and one 6-pin Quad/Tri motor outputs cables are included.

This special cable provides the typical 3-pin RC socket headers that connect directly to the ESC inputs. The cable will source power from the first ESC by default. A second cable connects directly to your receiver using single pin female headers.

Get all the firmware, stick commands, drivers, documents, arunio.

Everything you need to fly in one place!

MWC 2.3 https://www.dropbox.com/sh/tt3pa4tzdq7wif5/fnsdcnMPPl

MWC 2.2 https://www.dropbox.com/sh/5dwfcl8ar64tq43/HZM0bnsdrL

 

All the cables for Plug and Play for GPS, 3dRradios, and LED ring to the MEGA baord are configured to order.

RX connections:

Purple = throttle

Gray = Aileron

Brown = elevator

Orange = rudder

White = gear channel

Green = aux one channel

Blue = aux two channel

Yellow = aux three channel

Red=VIN = 5+ power to RX

Black=GND =  ground to RX

 

motor connections:

Yellow= front left

Green = back right

Blue=front right

White= back left

Mega v3.21 – Quality FC head to toe. In other words, business as usual.

 The Evolution of MEGA

Same Great sensors as The mega 2.0

5v and  3.3v regulator

Spektrum Satellite receiver connection,

ALL the missing Atmega2560 I/O pins that are needed for taking full advantage of the MultiWii and MPNG feature set.

• Atmega2560 – Super fast, tons of memory.
•  MPU6050 Six Axis Gyro/Accelerometer
•. MS5611 Barometer
• HMC5883L Magnetometer
• Servo output for camera pitch and roll control
• Supports direct connection of GPS module
• On-board USB connection for programming

Mounting: Standard Mk style mounting holes 45mm X 45mm 
Dimensions: 70x50x12mm
Weight: 16g

Pre-loaded with QUADX, and programed to fly almost out of the box with most any ESC’s

To reflash the board, using the IMU config as : //FFIMUv43

Comes with:

one radio r/x cable

If ordered with GPS, the quick connect cable with come to connect Flight controller to the GPS unit.