RTF BearHugESC 18Amp 2s-6s 3.0

This 18A Version uses higher rated top notch fets which are able to withstand higher currents compared to the 12A Version. Supporting the highest cell count for the Smallest ESC in its class, just 2g bare PCB. 2-6s compatible. Yes . up to SIX cell support.

RTF Bear HugESCs were developed to hug your multicopter frame, maximizing performance, so you can kiss your racing foes goodbye . Featuring ultra light weight construction with excellent thermal properties for an ESC – the MOSFETS are specifically selected to run BLHeli with the least amount of heat production and highest efficiency.  Users will need to install wires (INCLUDED). Clock and Data lines are on “easy” to solder for easy prgamming BLHeli 14.3.0.2 (multirotor) Installed and Tested

Enable Racing Mode! (Dampened Light Mode) – Enable racing mode! For True Plug and Play settings, more flying and less time on the bench. Racing mode is pre-programmed and optimized for best performance by quadcopter racers  – ready for just about any motors – OneShot is included/Ready – we recommend not  to alter our BL-Heli settings for racing quads. Race mode changes over 10 Settings for maximum performance: PWM Frequency/Damped, Motor Timing, Beacon strength/Delay,PPM MIN/MAX Throttle are set to maximum performance! Pair with a Flip32 for automatic detection of all the advantages of Oneshot123. Newest BLHeli 14.3 Firmware ships out pre-programmed and tested.

-Reverse motor direction easily
-Supports damped light mode,demag, timming, and countless other settings
– Pads on edge for easy programming ! (see pic)
– Advantages of further advancements in BLHeli by flashing new firmware
-Set other parameters such as beacon, PPM range etc
– Many setting for any  motor/battery/prop combo

DOWNLOAD THE BLHELISUITE  HERE

Features:
All Nfets – Newest BLHeli 14.3 Firmware
18Amp constant(In good air flow)
Easy to reach programing pads
NO BEC OPTO!
2s and 6S Capable (yes. 4S please)
Ultra light weight 2g PCB.  couple more grams with all motors and power wires.
400hz and 490hz compatible – DJi, naze32, cc & MultiWii tested with mni motors to 25,000rpm
Size:  22mmX12mm

new 3.0. New and Improved LDO, layout and pads, now with HIGHER RATED CAPACITORS INSTALLED & IMPROVE PAD AND PLACMENT. NOw Flashed with the newst BLHELI 14.3!  This 18A Version uses higher rated top notch fets which are able to withstand higher currents compared to the 12A Version.Supporting the highest cell count for the Smallest ESC in its class, just 2g bare PCB. 2-6s compatible. Yes. up to six (6s) cell support.

RTF Bear HugESCs were developed to hug your multicopter frame, maximizing performance, so you can kiss your racing foes goodbye . Featuring ultra light weight construction with excellent thermal properties for an ESC – the MOSFETS are specifically selected to run BLHeli with the least amount of heat production and highest efficiency.  Users will need to install wires (INCLUDED). Clock and Data lines are on “easy” to solder for easy prgamming. The newest BLHeli (multirotor) Installed and Tested

Enable Racing Mode! (Dampened Light Mode) – Enable racing mode! For True Plug and Play settings, more flying and less time on the bench. Racing mode is pre-programmed and optimized for best performance by quadcopter racers  – ready for just about any motors – OneShot is included/Ready – we recommend not  to alter our BL-Heli settings for racing quads. Race mode changes over 10 Settings for maximum performance: PWM Frequency/Damped, Motor Timing, Beacon strength/Delay,PPM MIN/MAX Throttle are set to maximum performance! Pair with a Flip32 for automatic detection of all the advantages of Oneshot123. Newest BLHeli 14.3 Firmware ships out pre-programmed and tested.

-Reverse motor direction easily
-Supports damped light mode,demag, timming, and countless other settings
– Pads on edge for easy programming ! (see pic)
– Advantages of further advancements in BLHeli by flashing new firmware
-Set other parameters such as beacon, PPM range etc
– Many setting for any  motor/battery/prop combo

Features
All Nfets – 14.3.0.2 Firmware
18Amp constant(In good air flow)
Easy to reach programing pads
NO BEC OPTO!
2s and 6S Capable (yes. 4S please)
Ultra light weight 2g PCB.  couple more grams with all motors and power wires.
400hz and 490hz compatible – DJi, naze32, cc & MultiWii tested with mni motors to 25,000rpm
Size:  22mmX12mm

3.0V  NOW SHIPPPING : HIGHER RATED CAPACITORS INSTALLED  :  IMPROVE PAD AND PLACMENT