RTF Mini-20A (Blue Series) SIMONK-(RAPIDESC)

The Mini 20A features a UBEC and is the smallest 20A ESC With a BEC built in, for the builds when one do not have to worry about another 5v power suppy to power there flight controller.

The RTF Mini 20 amp ESC with customized SimonK firmware including OneShot auto-detect . Small in size (27×14.5x6mm)  supporting 20A on 4s. The ESC comes pre-loaded with the newest firmware, which is compatible with new features like “OneShot” . No soldering a jummper pad required, it will auto-detect if OneShot is enabled), Comp PWM (Dambed light), compatible with all Lumenier motors up to 4 cell.

The RTF 20 amp AutoShot ESCs have been tested and are compatible with all of your motors and many more with , 2S-4S, both 5″ and 6″ props without sync loss issues or cogging.

The Simonk AutoShot firmware is pre-calibrated with endpoints 1060us – 1860us. This corresponds to the default endpoints in both Baseflight and Cleanflight. Therefore, “Calibration” procedure is not necessary.

Enable Racing mode:  We will turn on Comp_PWM + Motor_adacance timing. This can also be changed with the radip flash chrome app . All esc come with a bootloader.

Features

Active Braking / Damped Light / Comp_PWM
AutoShot (OneShot125 / FastPWM Auto Detect)
Customized to drive all motors without sync issues or cogging.
To enable new features on Baseflight:
– On Configuration tab, check “Enable OneShot” and “Enable FastPWM”
– Scroll down and click “Save”

To enable new features on Cleanflight:
-On Configuration tab, check the “Enabled” box next to “ONESHOT125” Feature
-Scroll down and click “Save”

Specifications

Max continuous load: ~20 amps
Burst Current: 30A/10sec
BEC: 5v/1amp max
Lipo Cells: 2 to 4 cells
Cables are fitted with female 2mm bullet connectors
Weight: 4g (board) 8g (total with wires and connectors)
High quality N-FET only flashed with SimonK firmware and 5v 1A BEC
Dimensions

27mm L x 14.5mm W x 6mm H
100mm signal wire / 5v power
50mm motor wires
70mm ESC power wires

Dampened Light supported – OneShot125  autodeacte Compatible

Specifications

• BlHeli: Dampend light supported and OneShot125 compatible
• Max continuous load: 20 amps
• Burst Current:  30A/30sec
• BEC: 5v/1amp max
• Lipo Cells: 2 to 4 cells
• Processor: Atmel
• Refresh Rate: 600hz
• Default timing: Medium ((Recommended for 2204) (Med-High Recommened for 2206))
• Servo Cable Flashable – via Afro Stick, MT1501, Or nano Flasher (Arduino Nano)

Dimensions

• 27mm L x 14mm W x 5mm H
• 10g with wires
• 4g no wires (bare)
• The Mini 20A features a UBEC and is the smallest 20A ESC With a BEC built in, for the builds when one do not have to worry about another 5v power suppy to power there flight controller.

  The RTF Mini 20 amp ESC with customized SimonK firmware including OneShot auto-detect . Small in size (27×14.5x6mm)  supporting 20A on 4s. The ESC comes pre-loaded with the newest firmware, which is compatible with new features like “OneShot” . No soldering a jummper pad required, it will auto-detect if OneShot is enabled), Comp PWM (Dambed light), compatible with all Lumenier motors up to 4 cell.

  The RTF 20 amp AutoShot ESCs have been tested and are compatible with all of your motors and many more with , 2S-4S, both 5″ and 6″ props without sync loss issues or cogging.

  The Simonk AutoShot firmware is pre-calibrated with endpoints 1060us – 1860us. This corresponds to the default endpoints in both Baseflight and Cleanflight. Therefore, “Calibration” procedure is not necessary.

  Enable Racing mode:  We will turn on Comp_PWM + Motor_adacance timing. This can also be changed with the radip flash chrome app . All esc come with a bootloader.

  Features

  Active Braking / Damped Light / Comp_PWM
  AutoShot (OneShot125 / FastPWM Auto Detect)
  Customized to drive all motors without sync issues or cogging.
  To enable new features on Baseflight:
  – On Configuration tab, check “Enable OneShot” and “Enable FastPWM”
  – Scroll down and click “Save”

  To enable new features on Cleanflight:
  -On Configuration tab, check the “Enabled” box next to “ONESHOT125” Feature
  -Scroll down and click “Save”

  Specifications

  Max continuous load: ~20 amps
  Burst Current: 30A/10sec
  BEC: 5v/1amp max
  Lipo Cells: 2 to 4 cells
  Cables are fitted with female 2mm bullet connectors
  Weight: 4g (board) 8g (total with wires and connectors)
  High quality N-FET only flashed with SimonK firmware and 5v 1A BEC
  Dimensions

  27mm L x 14.5mm W x 6mm H
  100mm signal wire / 5v power
  50mm motor wires
  70mm ESC power wires

  Dampened Light supported – OneShot125  autodeacte Compatible

  Specifications

  • BlHeli: Dampend light supported and OneShot125 compatible
  • Max continuous load: 20 amps
  • Burst Current:  30A/30sec
  • BEC: 5v/1amp max
  • Lipo Cells: 2 to 4 cells
  • Processor: Atmel
  • Refresh Rate: 600hz
  • Default timing: Medium ((Recommended for 2204) (Med-High Recommened for 2206))
  • Servo Cable Flashable – via Afro Stick, MT1501, Or nano Flasher (Arduino Nano)

  Dimensions

  • 27mm L x 14mm W x 5mm H
  • 10g with wires
  • 4g no wires (bare)